Contact Us

Fluid Loss Additives

The design properties of slurries are significantly influenced by the water content.  Thus, slurries that lose water can also be subject to a loss or degradation of design properties. There are a number of conditions that can induce fluid loss:

  • Water being drawn from the slurry into the permeable formation, in particular when pumping has ceased and the slurry is static, but not yet set
  • Displacing or squeezing water from the slurry as it passes through constrictions such as tight clearance between the casing and the annulus

Fluid loss additives help operators retain the key characteristics of their cement slurries, including viscosity, thickening time, density and compressive strength development.

Halad®-413 Fluid-Loss Additive
Provides excellent fluid-loss control in high temperature wells, especially when used on densified slurries or slurries with high salt concentrations due to its dispersing properties.
Halad®-862 Fluid Loss Additive
Developed as a less dispersive alternative to Halad-413 additive to meet response requirements in heavyweight slurries, seawater, and saturated salt designs.
Halad®-200L Fluid Loss Additive
Helps control fluid loss, viscosifies the slurry, does not retard the cement set, is salt-tolerant up to saturation, and is effective as low as 100°F (37.8°C) and higher than 400°F (204.4°C).
Halad®-567 Fluid Loss Additive
A fluid-loss additive made from synthetic polymer technology which is compatible with salt, seawater, and CaCl2 and effective up to 350°F (176.7°C) without over-retarding at temperatures as low as 80°F (26.7°C); it is not a strong dispersant so it can be used in normal and heavyweight slurries.
Halad®-322 Fluid-Loss Additive
A fluid-loss additive designed for use in low-temperature wells (below 180°F or 82.2°C) to prevent retardation of compressive-strength development; acts as a dispersant as well.
DeepFX™-L Additive
DeepFX-L additive: A single additive to provide fluid-loss control and shorten transition time to help address shallow water flow concerns.
Halad®-344 Fluid Loss Additive
Helps control fluid loss is non-retarding, and is compatible with freshwater and seawater.
Halad®-600 LE+ Fluid Loss Additive
Helps control fluid loss in environmentally sensitive areas between 125°F (51.7°C) and 300°F (148.9°C), acts as a mild retarder, gel breaker, and dispersant.
Halad®-688 and Halad®-688 EXP additives
A fluid-loss additive similar to Halad 344 additive intended for use with construction grade or off spec cements.
Halad®-23 Fluid Loss Additive
Helps control fluid loss, is effective in freshwater and saltwater slurries, is ideal for circulating jobs and for deep liner cementing, maintains fluidity, eliminates premature dehydration, and prevents bridging in a tight annulus when cementing is performed from 80°F (26.7°C) to 360°F (148.9°C).
Halad®-300L Fluid-Loss Additive
Designed to replace Halad-200L additive, it helps control fluid loss without breaking foamed cement structures and is effective from 100°F (37.8°C) and higher than 400°F (204.4°C).
Halad®-9 Fluid-Loss Additive
A blend of cellulose derivative and a dispersant developed for primary or squeeze operations between 60°F (15.6°C) and 300°F (148.9°C).
WaterWeb® Water Control
WaterWeb® Water Control Uses unique polymer chemistry to help create oil-water separation in the reservoir, impeding water flow and enhancing hydrocarbon flow to the wellbore.

Fluid Loss Additives

Filter By  
Количество записей на странице Show     results per page
  TitleНазвание  DateДата
Summary Summary WAC-9™ fluid-loss additive
WAC-9™ is a fluid-loss additive designed for use in gelled fracturing fluids. fracturing fluids.
Summary Summary Fluid Loss Additives
Our Case for Halliburton Additives is Water Tight. The Industry's Most Complete Line of Fluid Loss Additives Means We Can Tailor A Slurry Precisely To Your Well's Requirements — For The Most Effective Cementing Job Possible.
Summary Summary Halad®-567 Additive - A4
Halad®-567 fluid-loss additive is made from synthetic polymer technology. It is available as a powder or a 20% solution (Halad®-567L additive).
Summary Summary Halad®-600 E+ Additive -A4
Halad®-600 E+ additive helps control fluid loss in environmentally sensitive areas.
Summary Summary Halad®-9
Halad®-9 additive is a blend of a cellulose derivative and a dispersant. It provides fluid loss control in all API classes of cement.
Summary Summary Halad®-766
Halad®-766 fluid-loss additive can also be used as a retarder. Halad-766 fluid-loss additive is extensively used to retard foam slurries without reducing viscosity. Halad-766 fluid-loss additive is a derivitatized cellose that can be used for fluid loss and retardation in all API cement classes as well as Pozmix® cement. The tables below list the product specifications and part numbers for Halad-766 fluid-loss additive.
Summary Summary Halad®-300L Additive
Halad®-300L fluid-loss additive is an alternative to Halad®-200 additive.
Summary Summary Halad®-413
Halad®-413 fluid-loss additive can provide excellent fluidloss control in high-temperature wells, especially when used on densified cement slurries or slurries mixed with high salt concentrations.
Summary Summary Halad®-22A
Halad®-22A additive is a high-temperature fluid-loss control agent that functions effectively in freshwater and saltwater slurries.
Summary Summary Halad®-567 Additive
Halad®-567 fluid-loss additive is made from synthetic polymer technology. It is available as a powder or a 20% solution (Halad®-567L additive).
Summary Summary Halad®-23 Additive (Russian)
Halad®-23 -- Russian
Summary Summary Halad®-766 (Russian)
Halad®-766 fluid-loss additive can also be used as a retarder. Halad-766 fluid-loss additive is extensively used to retard foam slurries without reducing viscosity. Halad-766 fluid-loss additive is a derivitatized cellose that can be used for fluid loss and retardation in all API cement classes as well as Pozmix® cement. The tables below list the product specifications and part numbers for Halad-766 fluid-loss additive.
Summary Summary Halad®-23 Additve A-4
Halad®-23 additive is a high-temperature fluid-loss control agent that functions effectively in freshwater and saltwater slurries.
Summary Summary Halad®-23 Additve
Halad®-23 additive is a high-temperature fluid-loss control agent that functions effectively in freshwater and saltwater slurries.
Summary Summary Halad®-567 Additive (Russian)
Halad-567 Data sheet in Russian
Summary Summary Halad®-413 Additive A-4
Halad®-413 additive is a synthetic polymer that helps control filtrate loss in all cement conditions
Summary Summary Halad®-322 Additive (Russian)
Russian language version of Halad®-322 data sheet.
Summary Summary Halad®-413 Additive
Halad®-413 additive is a synthetic polymer that helps control filtrate loss in all cement conditions.
Summary Summary Halad®-447 Additive
Halad®-447 is a fluid-loss additive containing polyvinyl alcohol. This additive helps prevent fluid loss and gas migration in most API and lightweight commercial cements.
Summary Summary Halad®-413 Additive (Russian)
Halad®-413 -- Russian
Summary Summary Halad®-322 Additive -A-4
Halad®-322 is a fluid-loss additive designed for use in low-temperature wells. It can be used in wells with bottomhole circulating temperatures (BHCTs) of 180°F (82°C) and below.
Summary Summary Halad®-600 E+ Additive
Halad®-600 E+ additive helps control fluid loss in environmentally sensitive areas.
Summary Summary Halad®-600 E+ Additive (Russian)
Halad®-600 E+ -- Russian
Summary Summary Halad®-447 Additive (Russian)
Halad-447 Data sheet in Russian
Summary Summary Halad®-447 Additive A-4
Halad®-447 is a fluid-loss additive containing polyvinyl alcohol. This additive helps prevent fluid loss and gas migration in most API and lightweight commercial cements.
Summary Summary Halad®-322 Additive
Halad®-322 is a fluid-loss additive designed for use in low-temperature wells. It can be used in wells with bottomhole circulating temperatures (BHCTs) of 180°F (82°C) and below.
Summary Summary Halad-400L Fluid Loss Additive
Halliburton’s Halad®-400L fluid loss additive is a synthetic additive developed for temperatures from below 80°-400°F (27°-204°C) and for salt concentrations from zero percent to saturated salt concentrations. Halad-400L has been environmentally approved for use in the North Sea (exhibits biodegradability, low toxicity, and low bioaccumulation potential). This additive works without building viscosity and has a slightly dispersive character, thus the cement slurry remains thin. This additive is available as an aqueous liquid with a 22% activity.
Summary Summary Halad-400L Fluid Loss Additive
Halliburton’s Halad®-400L fluid loss additive is a synthetic additive developed for temperatures from below 80°-400°F (27°-204°C) and for salt concentrations from zero percent to saturated salt concentrations. Halad-400L has been environmentally approved for use in the North Sea (exhibits biodegradability, low toxicity, and low bioaccumulation potential). This additive works without building viscosity and has a slightly dispersive character, thus the cement slurry remains thin. This additive is available as an aqueous liquid with a 22% activity.
Summary Summary Halad®-344 - A4
Halad®-344 fluid-loss additive is especially useful in lightweight cementing compositions that often have long thickening times. The material is nonretarding, thus making good compressive strength development possible at low temperatures. Halad®-344 additive performs as well in seawater as in fresh water, and is compatible with retarders, dispersants, and calcium chloride (CaCl2).
Summary Summary Halad®-344 (Russian)
Halad®-344 fluid-loss additive in the Russian language
Summary Summary Halad®-344
Halad®-344 fluid-loss additive is especially useful in lightweight cementing compositions that often have long thickening times. The material is nonretarding, thus making good compressive strength development possible at low temperatures. Halad®-344 additive performs as well in seawater as in fresh water, and is compatible with retarders, dispersants, and calcium chloride (CaCl2).
Summary Summary Halad®-766 - A4
Halad®-766 fluid-loss additive can also be used as a retarder. Halad-766 fluid-loss additive is extensively used to retard foam slurries without reducing viscosity. Halad-766 fluid-loss additive is a derivitatized cellose that can be used for fluid loss and retardation in all API cement classes as well as Pozmix® cement. The tables below list the product specifications and part numbers for Halad-766 fluid-loss additive.
Summary Summary Halad®-300L Additive - A4
Halad®-300L fluid-loss additive is an alternative to Halad®-200 additive.
Summary Summary Halad®-300L Additive (Russian)
Halad®-300L fluid-loss additive is an alternative to Halad®-200 additive.
Summary Summary DeepFX-L Additive
DeepFX-L additive is a single additive to address two challenges designed to enable logistics efficiencies and to be blended with cementing systems to help address both shallow water flow and gas migration conditions.
Summary Summary Tuf Fiber™ 594 cement additive
When blended into cement slurry systems, Tuf Fiber™ 594 cement additive helps overcome lost circulation while improving wellbore strength by adding cohesiveness and increased ductility to the set cement sheath.
Summary Summary Overcoming Lost Circulation Across Brown Dolomite
An operator was incurring costs associated with loss of circulation events across the brown dolomite section of the Anadarko basin. These costs resulted from non-productive time, remedial operations expenses and fluid-replacement costs and ranged from $120,000-$170,000 (USD) on individual wells. Use of the Arx LCM package not only eliminated multi-stage cementing costs, but helped the operator avoid costs previously experienced due to loss of circulation events across the brown dolomite.
Summary Summary Halad®-413 Fluid-Loss Additive
Provides excellent fluid-loss control in high temperature wells, especially when used on densified slurries or slurries with high salt concentrations due to its dispersing properties.
Summary Summary Halad®-862 Fluid Loss Additive
Developed as a less dispersive alternative to Halad-413 additive to meet response requirements in heavyweight slurries, seawater, and saturated salt designs.
Summary Summary Halad®-200L Fluid Loss Additive
Helps control fluid loss, viscosifies the slurry, does not retard the cement set, is salt-tolerant up to saturation, and is effective as low as 100°F (37.8°C) and higher than 400°F (204.4°C).
Summary Summary Halad®-567 Fluid Loss Additive
A fluid-loss additive made from synthetic polymer technology which is compatible with salt, seawater, and CaCl2 and effective up to 350°F (176.7°C) without over-retarding at temperatures as low as 80°F (26.7°C); it is not a strong dispersant so it can be used in normal and heavyweight slurries.
Summary Summary Halad®-322 Fluid-Loss Additive
A fluid-loss additive designed for use in low-temperature wells (below 180°F or 82.2°C) to prevent retardation of compressive-strength development; acts as a dispersant as well.
Summary Summary DeepFX™-L Additive
DeepFX-L additive: A single additive to provide fluid-loss control and shorten transition time to help address shallow water flow concerns.
Summary Summary Halad®-344 Fluid Loss Additive
Helps control fluid loss is non-retarding, and is compatible with freshwater and seawater.
Summary Summary Halad®-447 Fluid-Loss Additive
Helps control fluid loss and gas migration in most cements at bottomhole circulating temperatures up to 210°F (99°C); above 350°F (176.7°C) it provides sedimentation and free-water control, chemical resistance, shear bonding properties, and thermal shock reduction.
Summary Summary Fluid Loss Additives
Halliburton's complete line of fluid loss additives help control fluid leakoff, these additives are particularly important in squeeze cementing and annular gas migration control.
Summary Summary Halad®-766 Fluid Loss Additive
A fluid-loss additive that can be used to retard cement, Pozmix® cement, and foam slurries without reducing viscosity
Summary Summary Halad®-600 LE+ Fluid Loss Additive
Helps control fluid loss in environmentally sensitive areas between 125°F (51.7°C) and 300°F (148.9°C), acts as a mild retarder, gel breaker, and dispersant.
Summary Summary Halad®-688 and Halad®-688 EXP additives
A fluid-loss additive similar to Halad 344 additive intended for use with construction grade or off spec cements.
Summary Summary Halad®-23 Fluid Loss Additive
Helps control fluid loss, is effective in freshwater and saltwater slurries, is ideal for circulating jobs and for deep liner cementing, maintains fluidity, eliminates premature dehydration, and prevents bridging in a tight annulus when cementing is performed from 80°F (26.7°C) to 360°F (148.9°C).
Summary Summary Halad®-300L Fluid-Loss Additive
Designed to replace Halad-200L additive, it helps control fluid loss without breaking foamed cement structures and is effective from 100°F (37.8°C) and higher than 400°F (204.4°C).
Summary Summary Halad®-9 Fluid-Loss Additive
A blend of cellulose derivative and a dispersant developed for primary or squeeze operations between 60°F (15.6°C) and 300°F (148.9°C).
Summary Summary WaterWeb® Water Control
WaterWeb® Water Control Uses unique polymer chemistry to help create oil-water separation in the reservoir, impeding water flow and enhancing hydrocarbon flow to the wellbore.
Related Information

Related Information Дополнительная информация

Resources